Search Results

While the initial development phase of Doppler Global Velocimetry (DGV) has been successfully completed, there remains a critical next phase to be conducted, namely the determination of an error budget to provide quantitative bounds for measurements obtained by this technology. This paper describes a laboratory investigation that consisted of a detailed interrogation of potential error sources to determine their contribution to the overall DGV error budget. A few sources of error were obvious; e.g., Iodine vapor absorption lines, optical systems, and camera characteristics. However, additional non-obvious sources were also discovered; e.g., laser frequency and single-frequency stability, media scattering characteristics, and interference fringes. This paper describes each identified error source, its effect on the overall error budget, and where possible, corrective procedures to reduce or eliminate its effect.

The new concept, a microwave-driven smart material actuator, was introduced to wirelessly drive actuators of space antennas and reflectors. For the proof-of-concept, a multilayer piezoelectric actuator integrated with a 3×3 rectenna was set up and tested within microwave field. The test results showed that the rectenna generates up to 73 V DC for a piezoelectric actuator and demonstrates a wide controllability by allowing several control parameters. For high power requirement and effective use of incident microwave, a power allocation and distribution (PAD) circuit and a voltage up-converter (VUC) were studied in corporation with the rectenna circuitry.

The first space flight cryogenic flexible diode heat pipes (CFDHPs) were developed and verified under micro-gravity conditions on the Space Shuttle during STS-94 (July 1997) and the previous, minimum mission STS-83 (March 1997). The heat pipe working fluids were oxygen (with an operating range of 60 to 145 Kelvin) and methane (95 - 175 Kelvin). The heat pipes were verified as part of the Cryogenic Flexible Diode Heat Pipe (CRYOFD) flight experiment. CRYOFD was the third and fourth flights of the Hitchhiker based Cryogenic Test Bed (CTB). CRYOFD was managed by the Air Force Research Laboratory (AFRL) Phillips Research Site with NASA's Goddard Space Flight Center (GSFC) co-sponsoring the experiment, the Air Force's Space Test Program (STP) and GSFC's Hitchhiker (HH) group provided the Shuttle integration and support. Jackson and Tull (J&T) and Swales Aerospace, Inc. (SAI) executed the program as a Phase II SBIR under the AFRL.

This paper presents a simplified orbit analysis program developed to calculate orbital parameters for the thermal analysis of spacecraft and space-flight instruments. The program calculates orbit data for inclined and sunsynchronous earth orbits. Traditional orbit analyses require extensive knowledge of orbital mechanics to produce a simplified set of data for thermal engineers. This program was created to perform orbital analyses with minimal input and provides the necessary output for thermal analysis codes. Engineers will find the program to be a valuable analysis tool for fast and simple orbit calculations. A description of the program inputs and outputs is included. An overview of orbital mechanics for inclined and Sun-synchronous orbits is also presented. Finally, several sample cases are presented to illustrate the thermal analysis applications of the program.

This paper has presented a technique for the determination of an optimal configuration of fuselage mounted piezoelectric actuators for active structural acoustic control of interior noise in aircraft. The technique has demonstrated much potential in preliminary experiments where actuators were configured to couple into the first principal component of the acoustically coupled fuselage vibration. In this test, average reductions of 6 dB at the error microphones and 4 dB at five auxiliary microphones were observed for a pure tone disturbance at the left forward engine pylon of a business jet. This disturbance was used to simulate an oscillating force due to engine unbalance.

Noise is a barrier issue for penetration of civil markets by future tiltrotor aircraft. To address this issue, elements of the NASA Short Haul (Civil Tiltrotor) [SH(CT)] program are working in three different areas: noise abatement, noise reduction, and noise prediction. Noise abatement refers to modification of flight procedures to achieve quieter approaches. Noise reduction refers to innovative new rotor designs that would reduce the noise produced by a tiltrotor. Noise prediction activities are developing the tools to guide the design of future quiet tiltrotors. This paper presents an overview of SH(CT) activities in all three areas, including sample results.

The need for highly accurate measurements of velocity, temperature, pressure and density has required the development of new experimental techniques. While the majority of these development efforts at NASA Langley are focused toward applications for aeronautical programs such as the High-Speed Civil Transport, Advanced Subsonic Transport, and the National Aero-Space Plane, a number are applicable to other fields. The intent of this paper is to review recent instrumentation developments and applications at NASA Langley Research Center that may have applications in automotive testing. Five experimental techniques are described along with recent results obtained in NASA facilities.

This paper describes recent research in integrated aerodynamic-performance design optimization applied to a supersonic transport wing. The subsonic and supersonic aerodynamics are modeled with linear theory and the aircraft performance is evaluated by using a complete mission analysis. The goal of the optimization problem is to either maximize the aircraft range or minimize the take-off gross weight while constraining the total fuel load and approach speed. A major difficulty encountered during this study was the inability to obtain accurate derivatives of the aerodynamic models with respect to the planform shape. This work addresses this problem and provides one solution for the derivative difficulties. Additional optimization studies reveal the impact of camber design on the global optimization problem. In these studies, the plan-form optimization is first conducted on a flat plate wing and camber optimization is performed on the resulting planform.

Human factors egress testing of the HL-20 Personnel Launch System, a reusable flight vehicle for Space Station crew rotation, was conducted in both the vertical (launch) and horizontal (landing) positions using a full-scale model. Ingress and egress of 10-person crews were investigated with volunteers representing a range of heights. For both the vertical and horizontal positions, interior structural keels had little impact on egress times which were generally less than 30 seconds. Wearing Shuttle partial pressure suits required somewhat more egress time than when ordinary flight suits were worn due to the larger helmet of the Shuttle suit.

The effect of different types of control force actuator models and geometries on the intensity flow between a cylindrical shell and the contained acoustic space has been analytically investigated. The primary source was an external monopole located adjacent to the exterior surface of the cylinder midpoint. Actuator models of normal point forces and in-plane piezoelectric patches were assumed attached to the wall of a simply-supported, elastic cylinder closed with rigid end caps. Control inputs to the actuators were determined such that the integrated square of the pressure over the interior of the vibrating cylinder was a minimum. Test cases involving a resonant acoustic response and a resonant structural response were investigated. Significant interior noise reductions were achieved for all actuator configurations. Intensity distributions for the test cases show the circuitous path of structural acoustic power flow.

A new approach for development of a 50-kW directly solar-pumped iodine laser (DSPIL) system as a space-based power station was made using a confocal unstable resonator (CUR). The CUR-based DSPIL has advantages, such as performance enhancement, reduction of total mass, and simplicity which alleviates the complexities inherent in the previous system, master oscillator/power amplifier (MOPA) configurations. In this design, a single CUR-based DSPIL with 50-kW output power was defined and compared to the MOPA-based DSPIL. Integration of multiple modules for power requirements more than 50-kW is physically and structurally a sound approach as compared to building a single large system. An integrated system of multiple modules can respond to various mission power requirements by combining and aiming the coherent beams at the user's receiver.

This study addresses the possibility of beaming laser power from synchronous lunar orbits (the L1 and L2 LaGrange points) to a manned long-range lunar rover. The rover and two versions of a satellite system (one powered by a nuclear reactor; the other by photovoltaics) are described in terms of their masses, geometry, power needs, mission and technological capabilities. Laser beam power is generated by a laser diode array in the satellite and converted to 30 kW of electrical power at the rover. Present technological capabilities, with some extrapolation to near future capabilities, are used in the descriptions. The advantages of the two satellite/rover systems over other such systems and over rovers with on-board power are discussed along with the possibility of enabling other missions.

This paper presents the conceptual thermal design and analysis results for the Spectroscopy of the Atmosphere using Far-Infrared Emission (SAFIRE) instrument. SAFIRE has been proposed for Mission to Planet Earth to study ozone chemistry in the middle atmosphere using remote sensing of the atmosphere in the far-infrared (21-87 microns) and mid- infrared (9-16 microns) spectra. SAFIRE requires that far-IR detectors be cooled to 3-4 K and mid-IR detectors to 80 K for the expected mission lifetime of five years. A superfluid helium dewar and Stirling-cycle cryocoolers provide the cryogenic temperatures required by the infrared detectors. The proposed instrument thermal design uses passive thermal control techniques to reject 465 watts of waste heat from the instrument.

Aerodynamic effects induced from vectoring an exhaust jet are investigated using a well established thin-layer Reynolds averaged Navier-Stokes code. This multiple block code has been modified to allow for the specification of jet properties at a block face. The applicability of the resulting code for thrust vectoring applications is verified by comparing numerically and experimentally determined pressure coefficient distributions for a jet-wing afterbody configuration with a thrust-vectoring 2-D nozzle. Induced effects on the body and nearby wing from thrust vectoring are graphically illustrated.

An investigation was conducted at the NASA Langley Research Center's Aircraft Landing Dynamics Facility (ALDF) to define the post-tire failure drag characteristics of the Space Shuttle Orbiter main tire and wheel assembly. Skid tests on various materials were also conducted to define their friction and wear rate characteristics under higher speed and bearing pressures than any previous tests. The skid tests were conducted to support a feasibility study of adding a skid to the orbiter strut between the main tires to protect an intact tire from failure due to overload should one of the tires fail. Roll-on-rim tests were conducted to define the ability of a standard and a modified orbiter main wheel to roll without a tire. Results of the investigation are combined into a generic model of strut drag versus time under failure conditions for inclusion into rollout simulators used to train the shuttle astronauts.

Laminar flow flight experiments conducted over the past fifty years will be reviewed. The emphasis will be on flight testing conducted under the NASA Laminar Flow Control Program which has been directed towards the most challenging technology application- the high subsonic speed transport. The F111/TACT NLF Glove Flight Test, the F-14 Variable Sweep Transition Flight Experiment, the 757 Wing Noise Survey and NLF Glove Flight Test, the NASA Jetstar Leading Edge Flight Test Program, and the recently initiated Hybrid Laminar Flow Control Flight Experiment will be discussed. To place these recent experiences in perspective, earlier important flight tests will first be reviewed to recall the lessons learned at that time.

Over the past three decades, the application of simulation facilities to manned space flight projects has increased chances of successful mission completion by revealing the capabilities and limitations of both man and machine. The Space Station era, which implies on-orbit assembly, heightened system complexity, and great diversity of operations and equipment, will require increased dependence on simulation studies to validate the tools and techniques being proposed. For this reason the Society of Automotive Engineers (SAE) undertook a survey of both the facilities available for and the research requiring such simulations. This paper was written to provide LaRC input to the SAE survey of simulation needs and resources. The paper provides a brief historial sketch of early Langley Research Center simulators, and the circumstances are described which resulted in a de-emphasis of manned simulation in 1971.

Current viscous drag reduction research explores the limits of practical applications of natural laminar flow (NLF) for airplane drag reduction. To better understand these limits, advanced measurement techniques are required to study the characteristics of laminar to turbulent boundary-layer transition. Recent NASA research indicates that the transition mode which involves laminar separation can be detected using arrayed hot-film laminar separation sensor concepts. These surface-mounted sensors can provide information on the location of the laminar separation bubble as well as bubble length. This paper presents two different laminar separation sensor configurations developed in the NASA program and presents results of wind-tunnel and flight evaluations of the sensors as tools to detect boundary-layer transition.

The condition of aircraft tires and runway surfaces can be crucial in meeting the stringent demands of aircraft ground operations, particularly under adverse weather conditions. Gaining a better understanding of the factors influencing the tire/pavement interface is the aim of several ongoing NASA Langley research programs which are described in this paper. Results from several studies conducted at the Langley Aircraft Landing Dynamics Facility, tests with instrumented ground vehicles and aircraft, and some recent aircraft accident investigations are summarized to indicate effects of different tire and runway properties. The Joint FAA/NASA Runway Friction Program is described together with some preliminary test findings. The scope of future NASA Langley research directed towards solving aircraft ground operational problems related to the tire/pavement interface is given.

A discussion is given of the ongoing research related to laminar flow airfoils, nacelles, and wings where the laminar flow is maintained by a favorable pressure gradient, surface suction or a combination of the two. Design methologies for natural laminar flow airfoil sections and wings for both low and high speed applications are outlined. Tests of a 7-foot chord, 23° sweep laminar-flow-control-airfoil at high subsonic Mach numbers are described along with the associated stability theory used to design the suction system. The state-of-the-art of stability theory is simply stated and a typical calculation illustrated. In addition recent computer simulations of transition using the time dependent Navier-Stokes (N-S) equations are briefly described. Advances in wind tunnel capabilities and instrumentation will be reviewed followed by the presentation of a few results from both wind tunnels and flight. Finally, some suggestions for future work will complete the paper.